Time and again one would want to reuse some materials for various needs. It could also be in an attempt to try and combine various them to come up with a unique product. An example of such material is a lead crystal. The discussion below explains the process of making holes using glasswork drilling jig, a tool used to make penetrations in a glass that allows boring.
There are various kinds of glass crystals in existence in the present times. They differ in thickness, durability strength depending on the purpose they are made for. The main factor considered when trying to hole these surfaces is the size of penetrations aimed at. This will dictate the tools to be used. Preferable bits and ball burrs made of diamond are recommended for the task.
Some of the main tools employed for the job include the ball burrs and the bits. These are used together and supplement each other. The burr will start to make a turf that the bit will hold onto and bore further. They are available in different diameters. The burr will make a mark that will prevent the relevant bit from skidding away from the spot when the operation is ongoing.
Others are a tray or a plan. This is a flat surfaced pan like container aimed at holding the liquid to be used as lubrication during the boring process. It will hold the object being worked on as well as the fluid chosen for the task. A wooden board is needed to help in preventing one from accidentally penetrating through the bottom of pan or tray.
The procedure for undertaking the process is not a difficult one. You need to first place the object into the tray or pan. Then fill with suitable lubricant preferably water. Make sure you fill to slightly above the said object. Do not forget to put the wooden board discussed above before embarking on the real working.
Then use the ball burr to have a divot on the surface of an object. Go on to switch the burr with a bit. Make sure the bit is not twisted, and it is in good condition. Ensure that it matches the size of shacks to be made. In case you want to make bigger holes, use smaller bits to make some and then use a big ball burr and bits to enlarge them.
As you bore, ensure that you are keeping the tip of the drill wet all through. Keep replacing the water with a clean one when continuing with the task. In case you have running water, then make sure it runs continuously throughout to remove particles dug from the surface.
It is advisable to bore at a slower pace while applying a little pressure. Once the bit has a good grip, you can then accelerate but keep to the levels that you feel the operation is smooth and quite comfortable. Over speeding is not recommended as it contributes to wearing out of drill head.
There are various kinds of glass crystals in existence in the present times. They differ in thickness, durability strength depending on the purpose they are made for. The main factor considered when trying to hole these surfaces is the size of penetrations aimed at. This will dictate the tools to be used. Preferable bits and ball burrs made of diamond are recommended for the task.
Some of the main tools employed for the job include the ball burrs and the bits. These are used together and supplement each other. The burr will start to make a turf that the bit will hold onto and bore further. They are available in different diameters. The burr will make a mark that will prevent the relevant bit from skidding away from the spot when the operation is ongoing.
Others are a tray or a plan. This is a flat surfaced pan like container aimed at holding the liquid to be used as lubrication during the boring process. It will hold the object being worked on as well as the fluid chosen for the task. A wooden board is needed to help in preventing one from accidentally penetrating through the bottom of pan or tray.
The procedure for undertaking the process is not a difficult one. You need to first place the object into the tray or pan. Then fill with suitable lubricant preferably water. Make sure you fill to slightly above the said object. Do not forget to put the wooden board discussed above before embarking on the real working.
Then use the ball burr to have a divot on the surface of an object. Go on to switch the burr with a bit. Make sure the bit is not twisted, and it is in good condition. Ensure that it matches the size of shacks to be made. In case you want to make bigger holes, use smaller bits to make some and then use a big ball burr and bits to enlarge them.
As you bore, ensure that you are keeping the tip of the drill wet all through. Keep replacing the water with a clean one when continuing with the task. In case you have running water, then make sure it runs continuously throughout to remove particles dug from the surface.
It is advisable to bore at a slower pace while applying a little pressure. Once the bit has a good grip, you can then accelerate but keep to the levels that you feel the operation is smooth and quite comfortable. Over speeding is not recommended as it contributes to wearing out of drill head.
About the Author:
Get a summary of the factors to consider when choosing a glasswork drilling jig supplier and more information about a reputable supplier at http://www.fenestrationtooling.com/aboutus.html now.
0 komentar:
Posting Komentar